Parts Cart

V8 Conversions

Items 1-15 of 56

Set Descending Direction
per page
Page
  1. S10 Transmission Mount

    $19.95
    S10 transmission mount for Turbo 350 or 400 transmission when swapping out the original . Will fit factory crossmember. Learn More
  2. LS Crank Hub Adapter Turbo 350 400 4.8, 5.3, 5.7, 6.0 , 6.2

    $21.95
    These LS1 flexplate adapters will allow you to use an older-style automatic transmission and torque converter on your LS1 engine. They are made of high-strength steel and feature a special tapered end for easy installation Learn More
  3. S10 V8 Upper Radiator Brackets

    $22.95
    This item is for the conversion radiator in the standard location which is on the back side or rear of the radiator support. Also need are the rubber insulators which are Not part of this kit. These are the top brackets only. Learn More
  4. Axle Set Back Plates 1/2"

    $27.95
    These plates will center the rear end in the wheel wells also may eliminate the need to shorten the drive shaft. The plates set the rear end back and stock u-bolts will work. Learn More
  5. S10 2.8 Frame Mounts

    $30.00
    Pair of 2.8 Frame Mounts (needed if truck came with other than 2.8 motor) Learn More
  6. Fan Temp Sensor

    $38.95
    Turns fan on/off at the desired temperature. Dial-adjustable 180-240F. Gives the freedom to set one temperature for occasional high-demand use, then reset for highway or day-to-day driving Learn More
  7. Upper Radiator Brackets Front Mount

    $39.95
    Radiator brackets fit early S10 when radiator is installed in the front mount postion. Please note some modifications are needed. Learn More
  8. S10 V8 Conversion Manual

    $44.95
    Stealth S10 V8 conversion manual Chevrolet V-8 into 1982-1993 Chevrolet S-10 trucks. This book also contains a short chapter on the V-8 swap into the New Body Style. Learn More
  9. LS LSX Engine Swap Adapter Plates Engine Mounts 4.8 5.3 5.7 6.0 6.2

    $45.95

    MADE IN USA

    Adapter plates are designed so that you can use the early three bolt mounts. Plates will adapt the LS1 four bolt mounts to the early three bolt style. This adapter kit will make you able to install the LS1 engine into Camaro Chevelle Nova Corvettes and Impala.

    This is the common mounting location for most LS swaps.

    If you desire to set the engine back to the original plane of the transmission use our popular #2370 part to move it back 1 inch.


    NOTE ADAPTER PLATES ARE DESIGNED FOR THE EARLY STYLE THREE BOLT CHEVORLET RUBBER MOTOR MOUNTS. SUCH AS SEAL POWER PART NUMBER 270-2283 or Energy Suspension 3-1114G

    Learn More
  10. A Body Frame Mounts BOP to Chevy

    $49.95
    A-body frame mounts to replaceBuick Oldsmobile Pontiac style frame mounts to Chevy type. These mounts bolt in with no welding and will be the base to convert your BOP A-body to Chevy style framemounts. With this mount in place you can convert to LS, SBC or BBC engines note the ear spacing is for the energy suspension 3-1114 width not 3-1117 Learn More
  11. S10 V8 SWAP 2WD Motor Mounts

    $49.95
    MADE IN USA Motor mounts for installing a small block Chevy V8 in your 2 wheel drive S10 truck, HD Steel construction. These S10 V8 swap mounts allow maximum adjustment of engine placement. These are proven to fit, THE BEST ON THE MARKET! ADAPTS TO 2.8L RUBBER FRAME MOUNTS ONLY, IF YOU HAVE A 2.2L, 2.5L OR 4.3L ORIGINALLY. YOU WILL NEED TO PURCHASE THEM WE SELL THEM FOR $28.00 A PAIR.. SEE #ssiA2435 http://s10v8.carshopinc.com/product_info.php/products_id/61/SSIA2435 MADE IN USA Learn More
  12. Fuel Pressure Regulator with Bypass

    $55.95
    This regulator is ready to install and is designed to be used with the factory in tank fuel pump. Regulator is a bypass style and is adjustable. Learn More
  13. S10 V8 4WD Motor Mounts

    $58.95
    Motor mounts for installing a small block Chevy V8 in your 4 wheel drive S10 truck, HD Steel construction. These S10 V8 swap mounts allow maximum adjustment of engine placement. These are proven to fit, THE BEST ON THE MARKET! Learn More
  14. LS GEN IV ENGINE LIFT PLATE

    $59.95
    LS1 GENIV ENGINE LIFT PLATE LS2 LS3 LS7 6.2L Congratulations you have found The new LS GEN 4 based lift plate. We produce this item in house it is precision cut on our cnc program to insure a perfect fit every time and then we have it zinc plated for long lasting durability. This plate eases installation of all LS based motors into your chassis, simply remove the intake manifold and the VALLEY cover and bolt this unit into place. It has three different lift points to help balance out your engine transmission combo during the install. Also works well as a storage cover for LS engines. If you have an LS1 Gen III with knock sensors in valley use part #2365 For the following RPO codes Vortec 4.8L LY2 2007-2009 L2O 2010- Vortec 5.3L LH6 2005-2009 LY5 2007-2009 LMG 2007- LC9 2007- LH8 2008-2009 LMF 2008- LH9 2010- LS4 2005-2009 LS2 2005-2009 Vortec 6.0L LY6 2007- L76 2007-2009 LFA 2008-2009 VVT,LIVC L96 2010- LZ1 2010- Vortec 6.2L L92 2007-2008 L9H 2009- L94 2010- LS3 2008- LSA 2009- LS9 2009- L99 2010- LS7 2006- Learn More
  15. LS Engine Mounts Full Size Truck 73-87

    $59.95
    Motor mount adapter plates for 1973-1987 Chevy and GMC 2 Wheel drive trucks. Theadapter mountsare forLS based engine swaps such as 4.8,5.3,5.7 and 6.0 Learn More

Items 1-15 of 56

Set Descending Direction
per page
Page