Learn More

2 1/4 diameter .240 hole size Learn More

23481 Chrysler MOPAR Upper Ball Joint stud Remover A B E Body

AMERICAN MUSCLE 23481  UPPER BALL JOINT STUD REMOVER

Use this American Muscle tool to remove the Upper ball joint from the knuckle. 

Place the tool between the upper and lower ball joint studs. Remove the upper ball joint stud nut. Put pressure on the tool and steadily increase the pressure. While applying pressure ,hit the knuckle with a hammer. The stud will pop out.  If not, try a little more pressure, then hit again. You nmay have to repeat several times 

American muscle uses CNC technology to ensure manufacturing quality and consistance in all its tools.

 Machined from quality USA  steel in the USA

Learn More

23441 Chrysler Upper Control Arm Bushing Sleeve Installer B Body

AMERICAN MUSCLE 23441  UPPER CONTROL ARM BUSHING SLEEVE INSTALLER 

Use this American Muscle upper control arm sleeve installer to press the sleeve on to the upper control rear bushing to achieve a tighter fit.

The American Muscle Sleeve is # 23450  

The upper control arm sleeve installer fits inside the bushing and pulls the sleeve into the proper position. 

This is a better solution than welding. 

American muscle uses CNC technology to ensure manufacturing quality and consistance in all its tools.

 Machined from quality USA  steel in the USA

Learn More

Ford V block 292-312 Cam Bearing Mandrel For Carshopinc Cam Bearing Driver ID of the mandrel is 1 inch for the Bearing Driver Learn More

LS Chevy GM Cam Bearing Mandrel For Carshopinc Cam Bearing Driver ID of the mandrel is 1 inch for the Bearing Driver Learn More

Ford Flat Head V8 Cam Bearing Mandrel For Carshopinc Cam Bearing Driver ID of the mandrel is 1 inch for the Bearing Driver Learn More

Pontiac V 8 Cam Bearing Mandrel For Carshopinc Cam Bearing Driver Will work on: 301,326,350,389,400,428,455 ID of the mandrel is 1 inch for the Bearing Driver Learn More

Buick V8 Cam Bearing Mandrel For Carshopinc Cam Bearing Driver for 231 350 400 455 ID of the mandrel is 1 inch for the Bearing Driver Learn More

Big Block Ford 390 460 Cam Bearing Mandrel For Carshopinc Cam Bearing Driver for 360 390 406 427 428 429 460 ID of the mandrel is 1 inch for the Bearing Driver Learn More

Big Block Chevy Cam Bearing Mandrel For Carshopinc Cam Bearing Driver ID of the mandrel is 1 inch for the Bearing Driver Learn More

Small Block Chevy Cam Bearing Mandrel For Carshopinc Cam Bearing Driver ID of the mandrel is 1 inch for the Bearing Driver Learn More

Ford Flat Head V8 Cam Bearing Mandrel For Carshopinc Cam Bearing Driver ID of the mandrel is 1 inch for the Bearing Driver Learn More

Torsion Bar Adjuster A, B, E body MOPAR

2 NEEDED PER CAR

Torsion Bar Adjuster Body Styles A and B&E Part No. 35612
Use this tool from American Muscle to adjust the tension on your torsion bar.
Most original torsion bar adjusters on 1960s and 70s muscle cars are likely to be rusted and worn and are subject to breakage during removal. Replace them with new equipment from American Muscle. 

American Muscle uses CNC technology to ensure manufacturing consistency of each replacement torsion bar adjuster, which is machined from quality steel. Just like the original equipment, the adjusting bolt has a 3/4 hex head, which makes it easier for you to use a wrench inside the assembly to make adjustments.

Machined from quality USA  steel in the USA

Learn More

MOPAR Torsion Bar Remover & Installer

The torsion bar remover and installing tool from American Muscle helps make it easier for you to complete either action with the torsion bar. 

To remove the torsion bar,release the tension on it remove the clip in the rear. Then clamp the tool to the bar and tap the tool with a hammer until the torsion bar is loose.  To install tap the tool with hammer to seat the the bar back in its original position and install clip.

American Muscle uses CNC technoligy to ensure manufacturing consistancy of each of its USA made tools. 

Learn More